ac-dc specification 120 watts single, dual & triple outputs convection-cooled 3?x 5?footprint high efficiency to 85% open frame, u-channel & covered versions low temperature option optional power fail detect signal SDS120 series input input voltage 90-264 vac (120-370 vdc) input frequency 47-63 hz input current 1.7 a at 115 vac 1.0 a at 230 vac inrush current <30 a at 115 vac <55 a at 230 vac power factor 0.97 typical earth leakage current <0.30 ma at 115 vac <0.75 ma at 230 vac input protection 3.15 a on board fuse output output voltage see table output voltage trim ?% output 1 only (3.3 v variant ?0%) initial set accuracy single output models: ?% multi-output models: ?% minimum load no minimum load required for single output models. for multi-output models see table. start up delay 2 s max start up rise time ? ms hold up time >16 ms line regulation 1% maximum, ?.5% typical load regulation 5% maximum, ?.0% typical transient response 4% max deviation, recovery to within 1% in 4 ms for a 50% load change ripple & noise 1% pk-pk typical, 20 mhz bw overvoltage protection 112-132% v1 only, recycle input to reset overload protection all outputs: 110-150% with auto recovery (primary power limit) short circuit protection trip & restart (hiccup mode), auto recovery temperature 0.04%/ c coefficient xppower.com general efficiency 80% typical, 85% max, 230 vac 100% load isolation 3000 vac input to output 1500 vac input to ground 500 vac output to ground switching frequency pfc 100 khz, pwm 67 khz power density 4.87 w/in 3 signals power fail detect = ttl active low, combined ac and dc ok signal (option) mtbf >100 khrs per mil-hdbk-217f environmental operating temperature 0 ? to +70 ?, derate linearly from 100% load at +50 ? to 50% load at +70 ?, low temperature option ?l?-40 ? cooling convection-cooled operating humidity 5-95% rh, non-condensing storage temperature -40 ? to +85 ? vibration 2 g on 3 axes emc & safety emissions en55022, cispr22 and fcc, part 15 level b conducted harmonic currents en61000-3-2 voltage flicker en61000-3-3 esd immunity en61000-4-2, level 2 perf criteria a radiated immunity en61000-4-3, 3 v/m perf criteria a eft/burst en61000-4-4, level 2 perf criteria a surge en61000-4-5, level 3 perf criteria a conducted immunity en61000-4-6, level 2 perf criteria a dips & interruptions en61000-4-11, 30% 10 ms, 60% 100 ms, >95% 5000 ms perf criteria a, b, b safety approvals en60950-1, ul60950-1, csa60950-1 per cul, ce mark lvd
17-apr-07 ac-dc 1.18 (30.0) 2.57 (65.3) 1.18 (30.0) 3.01+0.20 0.00 (76.4 +0.5 0.0) 3.20+0.20 0.01 ( 81.4 +0.5 -0.2 ) 4.49 (114.3) 0.10 (2.5) 5.00 (127.0) 4.49 (114.3) 4.00 (101.6) 0.25 (6.4) 3.90 (99.06) 2.70 (68.6) 0.55 (14.0) m3xp0.5 (mounting holes) x 4 dc output ac input 13 pfd 1 l n g p1 p2 0.25 (6.4) 1.54 (39.2) 3.20 ( 81.4 ) m3xp0.5 (mounting holes) x 3 SDS120 mechanical details models and ratings max. power output 1 output 2 output 3 model number (2, 4, 5) vnom imin imax tol. (1) vnom imin imax tol. (1) vnom imin imax tol. (1) 72.0 w 3.3 v 0.00 a 22.00 a 5% SDS120ps03b ? 110.0 w 5.0 v 0.00 a 22.00 a 5% SDS120ps05b ? 115.0 w 7.0 v 0.00 a 16.42 a 5% SDS120ps07b 120.0 w 9.0 v 0.00 a 13.33 a 4% SDS120ps09b 120.0 w 12.0 v 0.00 a 10.00 a 3% SDS120ps12b ? 120.0 w 15.0 v 0.00 a 8.00 a 3% SDS120ps15b ? 120.0 w 18.0 v 0.00 a 6.66 a 3% SDS120ps18b 120.0 w 24.0 v 0.00 a 5.00 a 2% SDS120ps24b ? 120.0 w 28.0 v 0.00 a 4.28 a 2% SDS120ps28b 120.0 w 36.0 v 0.00 a 3.33 a 2% SDS120ps36b 120.0 w 48.0 v 0.00 a 2.50 a 2% SDS120ps48b ? 120.0 w 3.3 v 1.50 a 15.00 a 5% 12.0 v 0.20 a 6.0 a 5% SDS120pd01b 120.0 w 5.0 v 1.50 a 15.00 a 5% 12.0 v 0.20 a 6.0 a 5% SDS120pd02b 120.0 w 5.0 v 1.50 a 15.00 a 5% 15.0 v 0.20 a 6.0 a 5% SDS120pd03b 120.0 w 5.0 v 1.50 a 15.00 a 5% 24.0 v 0.10 a 3.5 a 5% SDS120pd04b 79.5 w 3.3 v 1.50 a 15.00 a 5% 5.0 v 0.40 a 6.0 a 5% SDS120pd00b 120.0 w 5.0 v 1.50 a 15.00 a 5% -24.0 v 0.20 a 2.0 a 5% SDS120pd05b 120.0 w 28.0 v 0.39 a 3.92 a 5% 5.0 v 0.20 a 2.0 a 5% SDS120pd06b 91.5 w 3.3 v 1.50 a 15.00 a 5% 5.0 v 0.60 a 6.0 a 5% 12.0 v 0.00 a 1.0 a 5% SDS120pt00b ? 91.5 w 3.3 v 1.50 a 15.00 a 5% 5.0 v 0.60 a 6.0 a 5% -12.0 v 0.00 a 1.0 a 5% SDS120pt01b 120.0 w 3.3 v 1.50 a 15.00 a 5% 12.0 v 0.60 a 6.0 a 5% 5.0 v 0.00 a 0.8 a 5% SDS120pt02b 120.0 w 3.3 v 1.50 a 15.00 a 5% 12.0 v 0.60 a 6.0 a 5% -5.0 v 0.00 a 0.8 a 5% SDS120pt03b 120.0 w 3.3 v 1.50 a 15.00 a 5% 12.0 v 0.60 a 6.0 a 5% -12.0 v 0.00 a 0.8 a 5% SDS120pt04b 120.0 w 3.3 v 1.50 a 15.00 a 5% 12.0 v 0.60 a 6.0 a 5% 12.0 v 0.00 a 0.8 a 5% SDS120pt05b 120.0 w 5.0 v 1.50 a 15.00 a 5% 12.0 v 0.60 a 6.0 a 5% 5.0 v 0.00 a 0.8 a 5% SDS120pt06b 120.0 w 5.0 v 1.50 a 15.00 a 5% 12.0 v 0.60 a 6.0 a 5% -5.0 v 0.00 a 0.8 a 5% SDS120pt07b ? 120.0 w 5.0 v 1.50 a 15.00 a 5% 12.0 v 0.60 a 6.0 a 5% -12.0 v 0.00 a 0.8 a 5% SDS120pt08b ? 120.0 w 5.0 v 1.50 a 15.00 a 5% 12.0 v 0.60 a 6.0 a 5% 12.0 v 0.00 a 0.8 a 5% SDS120pt09b 120.0 w 5.0 v 1.50 a 15.00 a 5% 15.0 v 0.60 a 6.0 a 5% -15.0 v 0.00 a 0.8 a 5% SDS120pt10b ? 120.0 w 5.0 v 1.50 a 15.00 a 5% 15.0 v 0.60 a 6.0 a 5% 15.0 v 0.00 a 0.8 a 5% SDS120pt11b 120.0 w 5.0 v 1.50 a 15.00 a 5% 24.0 v 0.35 a 3.5 a 5% -24.0 v 0.00 a 0.8 a 5% SDS120pt12b 120.0 w 5.0 v 1.50 a 15.00 a 5% 24.0 v 0.35 a 3.5 a 5% 24.0 v 0.00 a 0.8 a 5% SDS120pt13b 120.0 w 5.0 v 1.50 a 15.00 a 5% 24.0 v 0.35 a 3.5 a 5% -12.0 v 0.00 a 0.8 a 5% SDS120pt14b 120.0 w 5.0 v 1.50 a 15.00 a 5% 24.0 v 0.35 a 3.5 a 5% 12.0 v 0.00 a 0.8 a 5% SDS120pt15b ? 120.0 w 5.0 v 1.50 a 15.00 a 5% 10.0 v 0.60 a 6.0 a 5% -10.0 v 0.00 a 1.0 a 5% SDS120pt16b 120.0 w 5.0 v 1.50 a 15.00 a 5% 10.0 v 0.60 a 6.0 a 5% 10.0 v 0.00 a 1.0 a 5% SDS120pt17b notes 1. total regulation includes initial set accuracy, line regulation and load regulation. 2. for optional pcb only version, delete suffix ??from model number. example SDS120ps03. 3. for non-standard voltages contact sales office. 4. for optional power fail detect circuit, add suffix ??to model number 5. for optional -40 ?c operation, add suffix ?l?to model number. notes: 1. optional power fail detect signal on ??versions only. standard models pin 13 is n/c. 2. i/p connector p1 mates with molex housing 09-50-3051 & molex 2878 series crimp terminal. 3. o/p p2 mates with molex housing 09-50-3131 & molex 2878 series crimp terminal. 4. for optional cover kit order part number SDS120 cover ? , to receive unit with cover fitted add suffix ??to model number (overall height is 1.73 (44.0)). 5. for mating connector kit order part number SDS120 con kit ? . 6. for cable harness order part number SDS120s loom ? for single output models & SDS120m loom ? for multi-output models. 7. din clips are available for alternate mounting order 2 x ?in clip? all dimensions are in inches (mm). weight: 0.77-0.99 lbs (350-450 g) approx. for pcb-only version, overall dimensions are max 5.00 x 3.00 x 1.44 (127.0 x 76.2 x 36.6). ? available from farnell. see pages 204-206. pin connections pin single dual triple 1 v1 v2 v2 2 v1 v2 v2 3 v1 v1 v1 4 v1 v1 v1 5 v1 v1 v1 6 v1 v1 v1 7 return common common 8 return common common 9 return common common 10 return n/c v3 11 return common common 12 return common common 13 pfd (1) pfd (1) pfd (1) power fail detect (pfd) is +5 v for normal operation. source current is 5 ma max. pfd is <0.4 v for either ac fail (<90 vac) or dc fail (<95% vnom). sink current is 10 ma max. +5 v pin 13 internal
|
